Magnus Mobility 551D Square Wheel May Assist in IEC EN 60601-1 Standard
The 551D Square Wheel Caster may assist in compliance with the new IEC/EN 60601-1 standard. This standard has been evolving for several years. In the case of casters, the standard calls for carts/medical equipment (ME) to be able to clear a tall obstacle, nominally a door sill, without damage to the equipment or need for the operator to lift the cart, risking personal injury.
DiCandia Route and Magnus Mobility Roll Into Bakeries With Hi Temp Wheels and Casters
A strategic partnership arrangement has been formed between DiCandia Route, the Italian manufacturer of this hi-temp wheel, and Magnus Mobility Systems Inc. Magnus is the leading, worldwide provider of motion control solutions including casters and wheels, gas springs, levelers, bearings, and accessories. Magnus combines the best of single-source convenience with the benefits of a global network. Strategic distribution and service centers enable Magnus to provide timely delivery of this important hi-temp wheel product.
Operating Rooms Need Square Wheels According to Magnus Mobility
Operating room floors obstructed by the power cords, connecting wires from equipment to the operating table, and various and assorted tubes present a labyrinth of obstacles. Most equipment used in hospitals rolls, since it is frequently used in multiple locations. Equipment in operating rooms must be removed so the theatre can be sanitized for the next procedure.
Magnus Mobility Talks FDA Approved Non-Toxic Lubricants
An ergonomically friendly work environment requires noise reduction. RTH wheels are a special proprietary high temperature aerospace rubber compound that cushions the loaded racks from vibration, reduce floor noise, and can be equipped with special noise eliminating bearings. The RTH wheels and the stainless steel casters available from Magnus Mobility are FDA/USDA approved for contact with food ingredients and are permanently lubricated with FDA approved, non-toxic lubricants.
Association of Operating Room Nurses Includes Wheels from Magnus Mobility
A strategic partnership has been formed between Steinco, known worldwide for extraordinary German engineering of caster wheels and Magnus Mobility Systems Inc. Magnus is the leading, worldwide provider of motion control solutions including casters and wheels, gas springs, levelers, bearings, and accessories. Magnus combines the best of single-source convenience with the benefits of a global network. Strategic distribution and service centers enable Magnus to provide timely delivery of the 551D Square Wheel Caster products.
Nurses Assoc. to Include Hi-Temp Wheel and Casters
The “Association of Operating Room Nurses” show will be held at the New Orleans Convention Center March 26-28. Magnus will be exhibiting in booth 4060. Featured will be the Steinco square wheel caster for medical carts and equipment and the DiCandia hi-temperature wheel for sterilization and autoclave carts.
Hi-Temp Wheel and Casters Better Than Traditional Wheels Says Magnus Mobility
Traditional wheels do not work in hi-temp situations. Traditional hi-temp phenolic wheels survive about 350-400°F intermittent temperatures (30 mins in/30 mins cool-off). The traditional wheels are hard and noisy when rolling on floors. The wheels run directly on the caster axle without lubricant; they squeak when in higher temperatures.
Magnus Mobility Medical Equipment Wheels Focus at Association of Operating Room Nurses
The “Association of Operating Room Nurses” show will be held at the New Orleans Convention Center March 26-28. Magnus will be exhibiting in booth 4060. Featured will be the Steinco square wheel caster for medical carts and equipment and the DiCandia hi-temperature wheel for sterilization and autoclave carts.
Perishable News Notes Bakery Hi-Temp Wheel from Magnus Mobility
A strategic partnership arrangement has been formed between DiCandia Route, the Italian manufacturer of this hi-temp wheel, and Magnus Mobility Systems Inc. Magnus is the leading, worldwide provider of motion control solutions including casters and wheels, gas springs, levelers, bearings, and accessories. Magnus combines the best of single-source convenience with the benefits of a global network. Strategic distribution and service centers enable Magnus to provide timely delivery of this important hi-temp wheel product.
Magnus Mobility Square Wheels May Assist in New IEC EN 60601-1 Standard for Medical Equipment
The 551D Square Wheel Caster may assist in compliance with the new IEC/EN 60601-1 standard. This standard has been evolving for several years. In the case of casters, the standard calls for carts/medical equipment (ME) to be able to clear a tall obstacle, nominally a door sill, without damage to the equipment or need for the operator to lift the cart, risking personal injury.